An injection well is a device that places fluid deep underground into porous rock formations, such as sandstone or limestone, or into or below the shallow soil layer. The fluid may be water, wastewater, brine (salt water), or water mixed with chemicals.
Definition
The U.S. Environmental Protection Agency (EPA) defines an injection well as "a bored, drilled, or driven shaft, or a dug hole that is deeper than it is wide, or an improved sinkhole, or a subsurface fluid distribution system". Well construction depends on the injection fluid injected and depth of the injection zone. Deep wells that are designed to inject hazardous wastes or carbon dioxide deep below the Earth's surface have multiple layers of protective casing and cement, whereas shallow wells injecting non-hazardous fluids into or above drinking water sources are more simply constructed.
Applications
Injection wells are used for many purposes.
Waste disposal
Injection wells are widely considered to be the best method for disposal of treated waste water. Unlike outfalls or other direct disposal techniques, injection wells utilize the earth as a filter to further clean the treated wastewater before it reaches the receiving water. This method of waste water disposal also serves to spread the injectate over a wide area, further decreasing environmental impacts.In waste water disposal, treated waste water is injected into the ground between impermeable layers of rocks to avoid polluting fresh water supplies or adversely affecting quality of receiving waters. Injection wells are usually constructed of solid walled pipe to a deep elevation in order to prevent injectate from mixing with the surrounding environment.
Critics of waste water injection wells cite concerns relating to the injectate polluting receiving waters. Most environmental engineering professionals, however, consider waste water treatment followed by disposal through injection wells to be the most cost effective and environmentally responsible method of waste water treatment. The only known alternatives to injection wells are direct discharge of treated waste water to receiving waters or utilization of the treated water for irrigation. Direct discharge does not disperse the water over a wide area; the environmental impact is focused on a particular segment of a river and its downstream reaches or on a coastal waterbody. Extensive irrigation is often prohibitively expensive and requires ongoing maintenance and large electricity usage.
Since the early 1990s, Maui County, Hawaii has been engaged in a struggle over the 3-5 million gallons per day of wastewater that it injects below the Lahaina sewage treatment plant, over the claim that the water was emerging in seeps that were causing algae blooms and other environmental damage. After some twenty years, it was sued by environmental groups after multiple studies showed that more than half the injectate was appearing in nearby coastal waters. The judge in the suit rejected the County's arguments, potentially subjecting it to millions of dollars in federal fines. A 2001 consent decree required the county to obtain a water quality certification from the Hawaii Department Of Health, which it failed to do until after the suit was filed.
Oil and gas production
Another use of injection wells is in natural gas and petroleum production. Steam, carbon dioxide, water, and other substances can be injected into an oil-producing unit in order to maintain reservoir pressure, heat the oil or lower its viscosity, allowing it to flow to a producing well nearby.
Waste site remediation
Yet another use for injection wells is in environmental remediation, for cleanup of either soil or groundwater contamination. Injection wells can insert clean water into an aquifer, thereby changing the direction and speed of groundwater flow, perhaps towards extraction wells downgradient, which could then more speedily and efficiently remove the contaminated groundwater. Injection wells can also be used in cleanup of soil contamination, for example by use of an ozonation system. Complex hydrocarbons and other contaminants trapped in soil and otherwise inaccessible can be broken down by ozone, a highly reactive gas, often with greater cost-effectiveness than could be had by digging out the affected area. Such systems are particularly useful in built-up urban environments where digging may be impractical due to overlying buildings.
Aquifer recharge
Recently the option of refilling natural aquifers with injection or percolation has become more important, particularly in the driest region of the world, the MENA region (Middle East and North Africa).
Surface runoff can also be recharged into dry wells, or simply barren wells that have been modified to functions as cisterns. These hybrid stormwater management systems, called recharge wells, have the advantage of aquifer recharge and instantaneous supply of potable water at the same time. They can utilize existing infrastructure and require very little effort for the modification and operation. The activation can be as simple as inserting a polymer cover (foil) into the well shaft. Vertical pipes for conduction of the overflow to the bottom can enhance performance. The area around the well acts as funnel. If this area is maintained well the water will require little purification before it enters the cistern.
Regulatory requirements
In the United States, injection well activity is regulated by EPA and state governments under the Safe Drinking Water Act (SDWA).EPA has issued Underground Injection Control (UIC) regulations in order to protect drinking water sources.
EPA regulations define six classes of injection wells. Class I wells are used for the injection of municipal and industrial wastes beneath underground sources of drinking water. Class II wells are used for the injection of fluids associated with oil and gas production, including waste from hydraulic fracturing. Class III wells are used for the injection of fluids used in mineral solution mining beneath underground sources of drinking water. Class IV wells, like Class I wells, are used for the injection of hazardous wastes but inject waste into or above underground sources of drinking water instead of below. Class V wells are those used for all non-hazardous injections that are not covered by Classes I through IV. Examples of Class V wells include stormwater drainage wells and septic system leach fields. Finally, Class VI wells are used for the injection of carbon dioxide for sequestration, or long term storage. Currently, there are no Class VI wells in operation, but 6 to 10 wells are expected to be in use by 2016.
Injection-induced earthquakes
A July 2013 study by US Geological Survey scientist William Ellsworth links earthquakes to wastewater injection sites. In the four years from 2010-2013 the number of earthquakes of magnitude 3.0 or greater in the central and eastern United States increased dramatically. After decades of a steady earthquake rate (average of 21 events/year), activity increased starting in 2001 and peaked at 188 earthquakes in 2011. USGS scientists have found that at some locations the increase in seismicity coincides with the injection of wastewater in deep disposal wells. Injection-induced earthquakes are thought to be caused by pressure changes due to excess fluid injected deep below the surface and are being dubbed “man-made” earthquakes.
No comments:
Post a Comment